Showing results: 646 - 660 of 1086 items found.
-
F-16 -
TestVonics, Inc.
The primary function of the Air Data Test System (ADTS) is to perform testing and fault isolation of pneumatic-type Units Under Test (UUTs). To test a UUT, the operator connects the associated Line Replaceable Unit (LRU) Integrated Test Adapter (ITA) to the rackmount Avionics Intermediate Shop (AIS) test station. The operator connects the ADTS to the IAIS via an RS-232 Interface and then finally, connects the UUT to the ADTS using the supplied cables and hoses.
-
MTL 15 | VP 700006 -
Maschinenbau Haldenwang GmbH & Co. KG.
The MTL 15 test container works completely independently thanks to the optionally available, fully integrated power generator. Equipped with a hydraulic set-down device including cable remote control, the test system can be set up within 15 minutes and is therefore ideal for changing locations.
-
CableJoG 128 -
CableJoG Ltd
The CableJoG 128 can test up to 128 individual connections of all manufacturers of connectors. This simple test instrument stores up to 55 separate connection configurations. Each cable that is tested is compared with the configuration stored in its memory to produce a pass/fail indication of each pin connection.
-
CableJoG 256 -
CableJoG Ltd
The CableJoG 256 can test up to 256 individual connections of all manufacturers of connectors. This simple test instrument stores up to 12 separate connection configurations. Each cable that is tested is compared with the configuration stored in its memory to produce a pass/fail indication of each pin connection
-
Networked Communication Solutions, LLC
Handheld T1/E1 trouble shooting tool provides the test access capability of a cross-connect panel (DSX), in a small, convenient, handheld package. It saves time often wasted while deciphering test connections on network equipment and simplifies the patch cable selection required for maintenance and installation.
-
Tokyo Electronics Trading Co., Ltd.
This LCD failure analyzer provides test patterns and programmable power supplies for the LCD unit test. R, G, B signals are applied to the LCD unit under test. Compact control box connected by a cable allows test pattern selection, gray scale control, cursor location and scan direction. If PC is connected through RS-232C port, complex test sequence can be programmed. It is applicable to the production test, design verification, quality control and failure analysis.
-
T015-POE -
Tripp Lite
The T015-POE Network and PoE Tester consists of an emitter and a remote. Its functions include standard and non-standard PoE equipment detection, PoE power online test, network cable continuity test, DC power test and switch loopback test. It is a practical tool for technical personnel to use during installation and maintenance of security monitoring equipment, communications wiring, integrated wiring and other weak-current systems.
-
CAA-100 -
ShinewayTech
ShinewayTech® CAA-100 cable & antenna analyzer can test Return Loss and VSWR of load’ frequency. Also can get Return Loss, VSWR of DTF (distance-to-fault) and Cable Loss. Users can be easy to know the connection of cable & antenna system is reliable whether or not. CAA-100 series with frequency range 25MHz-4GHz and 60dB dynamic range can suitable for 2G/3G/4G/WiMAX system etc. CAA-100 series is the necessary measuring instrument for the new generation of wireless network development, upgrade and maintenance.
-
50211 -
Sonin
The Sonin Moisture Test Meter offers additional features & performance beyond those of the Moisture Test Tool. The meter’s contact probes are at the end of 3 foot coiled cable for detecting moisture in difficult to reach locations. Scale & reference chart correlate relative and moisture percentage readings
-
postrd -
PC Engines Gmbh
remote display kit for post4d, not RoHS compliant (can be considered test equipment, not subject to RoHS). Connects to PC Engines post4d PCI POST card (will not work with post2b or post5a). 20 inch cable, place display in a more accessible location. Ideal for software development or test fixtures.
-
Extech Instruments Corporation
An electronic tool for electricians, alarm, cable installers and others who routinely need to check circuits for continuity and also identify cables and wires. It allows a single user to quickly identify and label two wires even when the wire ends are located in different rooms. It can accommodate test wire lengths up to 10,000-feet (3,000 meters), 26-gauge minimum.
-
Eclypse International
A testing procedure designed to thoroughly test the electrical characteristics of a wire or cable, may require additional test points to connect the end points of all conductive paths. The changing and alteration of Test Adapter Cables (TACs) would become obsolete when having access to one or several expansion units. Increased testing efficiency alleviates the long, drawn out down times of the disabled aircraft while improving product readiness. Additional time can be spent on troubleshooting and problem identification and will not require the user to unhook and connect TACs to different matrices. Adding additional expansion units will save the user time, money, and effort.
-
Amphenol Fiber Systems International
Amphenol Fiber Systems International (AFSI) has developed the Loopback TFOCA and TFOCA-II® plug configuration as an aid to system maintenance and troubleshooting of the tactical cable reels and systems that use them. The Loopback plugs come in a variety of configurations from 0 dB to -23dB to simulate a system operational condition. The use of the Loopback plug enables a technician to test a cable reel in the bi-directional mode by simply swapping leads on the test meter, thus saving considerable time and effort in establishing a systems operational status.
-
781887-01 -
NI
Connects measurement and signal generation devices. Model options include industry-standard coaxial connector types including BNC, SMA, SMB, and MCX. Long cables can act as antennae picking up extra noise that can affect measurements, so ensure you select only the length required for your test system. Also look at the impedance of your test system and consider buying a cable with the same impedance. Matched impedance can maximize the power transfer or minimize signal reflection from the load of your system.
-
AF-OLK5NNextGen Series -
Advanced Fiber Solutions
The AF-OLK5NNextGen series test kits are the latest addition to the AFS product family. This inexpensive optical test kit is the complete solution necessary for the installer to test and trouble shoot both multimode and single mode fiber optic systems. These test kits are designed to allow testing of all parameters of fiber optic networks, including output power levels from the fiber, coupled source power and attenuation loss in a cable.
